CT2070 Large Bar-Height Table Base

The FLAT Tech CT2070 is a Large Bar-Height Table Base built for elevated seating with a 36 inch by 36 inch footprint and pre-installed FLAT Equalizers. This Large Bar-Height Table Base settles under light pressure and then locks so every table stands steady on floors that are not perfectly flat. With a cast iron frame and textured black finish, it is ready for daily service in busy bar areas. Because the mounting plate measures 17 inches by 17 inches, you can pair tops up to 47 inches round or 40 inches square. Finally, the four-point stance provides firm contact and smooth resets during peak hours.

At a Glance

Type: Bar-height cross base. Spread: 36 inch × 36 inch. Column: 4 inch round. Mounting plate: 17 inch × 17 inch. Finish: Textured black. Leveling: FLAT Equalizers. Best for: Tabletops up to 47 inch round or 40 inch square.

The FLAT Tech bases deliver precision and durability for commercial tabletops in demanding hospitality settings. Because each base uses a leveling or hydraulic system, the surface stays stable even when the floor is uneven. In addition, the cast iron build and textured finish resist wear from high traffic and frequent resets. Furthermore, the modular design lets you match height, spread, and mounting plate to your tabletop size and style. Finally, whether you plan bar-height groupings or large communal tables, these bases give your layout the confidence and finish guests expect.

Why Choose a Large Bar-Height Table Base

This model offers wide reach and steady contact for large bar-height tables. Each Equalizer adjusts independently, then locks in place as light pressure is applied at the edge. As a result, staff can realign tables quickly, reduce wobble complaints, and keep wide tops level through service. In high turn zones, that stability helps servers move faster and land plates with confidence. With this setup, you gain elevated seating durability and clean seams where tables meet.

Size and Compatibility

Base footprint: 36 inches × 36 inches
Column diameter: 4 inches
Mounting plate: 17 inch × 17 inch
Recommended tabletop: up to 47 inch round or 40 inch square

The Large Bar-Height Table Base pairs well with large solid wood or composite tops. Verify the underside can accept the 17 by 17 inch mounting zone and hardware. For dense hardwoods, confirm total mass ahead of install to preserve level performance. If you need the same spread in dining height, see CT2068. For a 22 by 30 bar-height footprint, compare CT2022. When heavier spans or added mass are required, review CT2036. To explore an alternate column or plate style, consider CT2087 or the versatile CT2071.

Use Cases

Large bar-height dining tables in restaurant and lounge areas
High-top communal layouts that join multiple tops together
Spaces that need steady surfaces for shared plates and drinks

Request More Info Now!

Installation and Setup Tips

Center the 17 inch mounting plate under your tabletop and mark pilot holes. Next, drill with the correct bit for your material, then secure all approved fasteners. Stand the table upright, apply light pressure to each edge, and allow the Equalizers to adjust until all feet make contact. Finally, confirm firm contact at four points and check seam height where tables meet for groups.

Pro Tip

For heavy solid wood tops, keep the center of gravity balanced and mount over structural bracing to reduce stress where floors vary slightly.

Technical Specifications

Model: FLAT Tech CT2070 (KX36 EQ)
Height: 40.75 inches (bar height)
Base spread: 36 inch × 36 inch
Top plate: 17 inch × 17 inch
Column: 4 inch round
Material: Cast iron
Finish: Textured black / powdercoat
Leveling system: FLAT Equalizers
Recommended top size: Up to 47 inch round or 40 inch square
Approximate base weight: 50 to 52 lb

Care and Maintenance

Clean with a soft cloth and mild soap. Avoid strong solvents that can dull the finish. Check the feet for debris and verify smooth motion before peak shifts. If glide movement becomes stiff, clear the contact points and retest. With this routine, the base stays level and presentable through daily use.

Featured Answer

Why choose a Large Bar-Height Table Base for big bar-height tables?

A Large Bar-Height Table Base supports oversized tabletops with four-point stability, locking feet, and balanced weight distribution, ideal for serving large groups in elevated seating. Combine CT2070 with our solid wood bar-height tops for a strong pairing that performs shift after shift.

Why Order From TimeWorn Wood

Pair CT2070 with our solid wood restaurant tabletops. We size, pre-drill, and finish each top for daily commercial use, then crate and ship nationwide with protection at edges and corners. We also help you set plate patterns, insert plans, and base spacing to match your layout so installation feels predictable and quick. Finally, our guidance on care and resets keeps the experience steady through every shift and season.